East End Assemblies

East End Assemblies We offer ‘Design for Manufacturing’ solutions to companies of all sizes and industries.

5 more big tips for desoldering:Minimize time Components & Board are at high tempsMatch your Solder Wick Width to Contac...
06/11/2026

5 more big tips for desoldering:
Minimize time Components & Board are at high temps
Match your Solder Wick Width to Contact Pad
Match Soldering Iron Tip to Braid Width
Clip used Desolder Wick after use
Match flux to cleaning process: (3 types are Rosin, Unfluxed, and No Clean)

If you're a beginner, the most straightforward technique (though rigorous) is grinding and scraping. This involves the u...
06/10/2026

If you're a beginner, the most straightforward technique (though rigorous) is grinding and scraping. This involves the use of a scraper, knife, or pick and a bit of elbow grease. One can expedite the process with mechanical erasers.

To understand some tips, one must first know what tools can be used for desoldering. While there's a variety of tools & ...
06/09/2026

To understand some tips, one must first know what tools can be used for desoldering. While there's a variety of tools & companies, here are the main tools you'll need:
Soldering Iron
Soldering Wick
Desoldering Braid & Iron
Desolder Pump and Iron
Power Desoldering Station

Key design parameters for power amps are frequency response, gain, noise, and distortion. These are interdependent; incr...
06/04/2026

Key design parameters for power amps are frequency response, gain, noise, and distortion. These are interdependent; increasing gain often leads to undesirable increases in noise and distortion. While negative feedback actually reduces the gain, it also reduces distortion.

While the input signal to an audio power amplifier may measure only a few hundred microwatts, its output may be vary bas...
06/03/2026

While the input signal to an audio power amplifier may measure only a few hundred microwatts, its output may be vary based on its use; from a few watts for small consumer electronics devices, to several thousand watts for a nightclub or tens of thousands of watts for a concert.

An audio power amplifier low-power electronic audio signals, like from electronic radios or instruments, to a level that...
06/02/2026

An audio power amplifier low-power electronic audio signals, like from electronic radios or instruments, to a level that is high enough for driving loudspeakers or headphones. In all sounds systems, it's the final stage in a typical audio playback. power

Electric Piano can refer to any of the following:Struck strings (grand/upright with strings and hammers)Struck reeds (fl...
05/28/2026

Electric Piano can refer to any of the following:
Struck strings (grand/upright with strings and hammers)
Struck reeds (flat steel reels struck by felt hammers)
Struck tuning-forks (2 vibrating parts)
Plucked reeds (saturated leather strike metal reeds)

An electric piano is a musical keyboard where sound is produced by means of mechanical hammers striking metal strings or...
05/27/2026

An electric piano is a musical keyboard where sound is produced by means of mechanical hammers striking metal strings or reeds or wire tines leading to vibrations which are then converted into electrical signals by pickups that are connected to an amplifier & loudspeaker.

Because of the sophistication of electronic instruments, East End Assemblies has been given jobs in music. Take the keyb...
05/26/2026

Because of the sophistication of electronic instruments, East End Assemblies has been given jobs in music. Take the keyboard or electric piano. Essentially a computer you play, the keys can hold more extensive sounds as well as be more portable than a grand piano.

For successful use of a stencil, its thickness must be properly calculated; otherwise, the paste could be held by the in...
05/21/2026

For successful use of a stencil, its thickness must be properly calculated; otherwise, the paste could be held by the inner walls of the aperture leading to the board to not work. Here is a formula for deciding on your stencil's thickness

Address

12 Old Dock Road
Yaphank, NY
11980

Opening Hours

Monday 8am - 8pm
Tuesday 8am - 8pm
Wednesday 8am - 8pm
Thursday 8am - 8pm
Friday 8am - 8pm
Saturday 10am - 4pm
Sunday 12am - 12:15am

Telephone

+16312055570

Website

Alerts

Be the first to know and let us send you an email when East End Assemblies posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Contact The Business

Send a message to East End Assemblies:

Shortcuts

Share

Category