AerobTec

The AerobTec company is engaged in the development, manufacturing and sales of high quality electron

23/02/2021

Hi Multiplex telemetry users. Did you know you can now configure bus addresses according to your needs?
It works for:
Altis v4
Altis nano
Altis GPS
Altis GPS2

22/07/2020

Announcement - new firmware!

Hello everyone,
these days new firmware for Altis nano and Altis v4+ have been released.
For Altis v4+ it is 5.8 for FAI F5J competitions.
For Altis nano it is 5.3 for FAI F5J competitions.
Both of them use the new rules valid officially since 2020, but both of them are waiting for their official approval.
Some of the organizers still prefer to use the previously approved firmwares 5.7 abd 5.2. and people are asking where to get them.
So they are available as a file at our website for download.
https://aerobtec.com/altis-nano/
https://aerobtec.com/altis-v4/
You can flash them by using File option in the Firmware upgrade wizard as shown on the picture.

23/04/2020

Beside of working for our customers AerobTec is also helping hospitals with shields so this tough period is overcome as soon as possible.

03/01/2020

Dear customers and fans, we wish you Happy New Year 2020. Let's start it with introduction of F5K competition support for Altis nano.

03/09/2019

WARNING - cable issue!!!

Dear customers,
based on several reports received from some of you in August this year we discovered that some of the devices have an issue with the input or output cables caused by our cable supplier. It seems some of the cables have incorrect crimping of the wire which was not discovered during the quality check, since the devices behaved normally and there was no suspicion about it.
The crimping issue might lead to interrupted of some of the connections on the way between the receiver and ESC which might have its consequences. Therefore it is recommended to pay appropriate attention to it.

We identified that the affected devices are Altis v4+ delivered mostly in the first half of 2019 and the serial numbers are from the range 464912388 to 498073604. It is not excluded that some other devices are affected as well – you can check also other devices. We had also one report on Device Terminal cable affected by this but at the moment there is no further indication if it is a single case or if it is related to the same issue.

It is recommended to check the cables according to following:
• Test the device in plane on ground
• Plug Altis between the receiver and ESC
• Run the motor
• Move the cable near connector in order to detect possible disconnection of the cable.
• Other check consists of trying to pull the cable from its housing (disconnected from plane). Hold the housing and pull the cable with a moderate force. You can also try it separately with all three wires entering the housing. If the wires are loosen easily, you probably have one of the affected devices.

If you detected that your device is affected by the problem or you have doubts about it feel free to contact us and send the device for replacement or repair for free.
If you decide to repair it yourself, please contact us and let us know about your case.

We are now in contact with the cable manufacturer so the issue does not occur again and we will extend the quality check during manufacturing steps.

We would like to apology for the inconveniences caused by the mentioned issue and we believe you will stay loyal to our products.

14/06/2019

Do you need to measure the power from your battery to your plane? Do you need to know the consumed energy or switch of the motor after some energy is consumed? Do you need to see the battery current and voltage? It is so easy! You can do it with our new Power Sensor connected to Altis.

03/09/2018

Heute haben wir Aerobtec Tag. Die gesamte Mannschaft vertraut auf die Logger Altis V4+ und Altis Nano. Vielen Dank an Aerobtec für die tolle Unterstützung!

13/04/2018

Altis nano is experiencing its first competition this weekend. Of course it wouldn't be possible without the certification from FAI.
More info on Altis nano is available at http://aerobtec.com/altis-nano/

05/04/2018

Thank you all for participation in our contest. The winners are Jakub Cirkva, Jason David Hyatt and Roy Dor.

29/03/2018

Altis nano is coming very soon and we have an interesting contest for you. Write a short message to us describing why you should have the Altis nano among the first users. We will choose three best winning participants. Do not forget that sharing this post among your friends might also increase your chances.
The deadline is Wednesday, April, 4th, 2018 at 18.00 UTC.
You still have chance.

01/02/2018

Some new detailed pictures of Altis nano. Is there anything you would like to see on the high contrast OLED display?

29/01/2018

You are the witness of the first public photo of Altis nano accompanied with its older Altis brothers.
It is the smallest competition altimeter with high contrast OLED display in the world.
Is Altis nano worth its name? Make your own opinion! 29x11.5mm and less than 5g inc. JR cables.
And of course! Almost unlimited competition settings, telemetry support and other features as you are already used to in Altis line.
More info is coming soon. Stay tuned!

Address

Ilkovičova 3
Bratislava
84104

Website

http://www.aerobtec.com/

Alerts

Be the first to know and let us send you an email when AerobTec posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Contact The Business

Send a message to AerobTec: