TiePie engineering

26/05/2026

New features in Multi Channel oscilloscope software version 1.49

New serial communication decoders

Four new serial communication decoders are added to the software. It is now possible to decode messages from

- LIN
- SAE J2716 SENT
- FlexRay
- DMX512

buses, to diagnose the systems that use them.

Extract values from a communication

When a serial communication, like e.g. CAN, LIN or SENT is decoded, a stream of data is obtained. This data can be shown in a table, but it is much more useful if a specific value in that data stream can be isolated and monitored, either in a graph, in a meter or in a table. The Value Extractor I/O can be used to extract such values from the data stream and present them in a graph, meter and/or table sink.

Filtering table contents

When a serial communication, like e.g. I2C, LIN or SENT is decoded, a stream of data is obtained. This data can be shown in a table, but that can give an overwhelmingly full table. Using the new versatile filtering option, it is possible to show just the exact data you need to.

Several other additions and improvements are made to the software.

Read more at https://www.tiepie.com/news/3968

Download and install the new software to make sure you can use all new features!

Version 1.49 of the Multi Channel oscilloscope software is now available for download.

11/11/2025

MultiScope:
the solution for your multi signal measurement challenges

Do you need a 6 channel oscilloscope? Or you require an 8 channel digitizer? Maybe even a 10 channel DAQ or 12 channel data acquisition system? Or still more? With one or more Arbitrary Waveform Generator outputs?

Now create your own digitizer with unprecedented possibilities and specifications.

- USB versions for all Handyscope series and WiFi versions for all WiFiScope series
- Plug-and-play for immediate data acquisition
- Operate with different units to build your own digitizer
- Very high accuracy for time (1ppm) and amplitude (0.1% typical)
- 8, 12, 14 and 16 bit resolution
- Continuous data transfer streaming of 200 MSa/s each instrument, e.g. 10 instruments gives a continuous data stream of 2 GSa/s
- Sophisticated SDK and a very extensive API for OEM Solutions
- API with support for various languages
- Any form of multi-channel system can be created
- Accelerating product development and reducing costs for your customer​​

All the hard work has already been done.
Start your own DAQ solution today.

TiePie engineering MultiScopes offer instruments with any number of input channels you need. These can be single-ended input channels or differential input channels or a mix of both.

Read more: https://www.tiepie.com/en/news/3951

12/06/2025

The new standalone logging option L for the WiFiScope WS6 - 1000XM makes it possible to use the WiFiScope WS6 fully autonomously, performing standalone measurements. Setup the instrument, start measuring and then disconnect the computer, leaving the instrument to continue measuring completely by itself. Measured data is stored on a solid state disk in the instrument.

For more info, see

The new standalone logging option L for the WiFiScope WS6 - 1000XM makes it possible to use the WiFiScope WS6 fully autonomously, performing standalone measurements.

19/03/2025

Multi Channel software version 1.48 is released.
Many changes are made to add new functionality and to improve operating the software.

- Schematic drawing measurement setups

The Object Tree can now be switched to a schematic representation. It then shows all available objects like instruments, graphs, meters, I/Os etc. in a schematic representation, using blocks for all objects. All connections between inputs and outputs are shown as well. Where possible, the same color for the connections is used as the corresponding signal lines in the graphs.

In the Object schema you can add and remove objects and make connections between inputs and outputs of objects, by dragging lines between outputs and inputs. That allows to perform the required calculations on the measured data and to display the data in meters and graphs.

- Standalone measuring

With versions of the WiFiScope WS6 - 1000XM with option L, it is possible to perform standalone measurements. Once the instrument is setup and measuring is started, it no longer requires a connection to the computer to perform measurements. The software can be closed and the computer can be used for another task. As long as the instrument is provided with power, it will perform measurements, which are stored on an internal solid state disk.

When the instrument is operating standalone, the software can connect to it, to download and view saved measurements, to send notifications when e.g. a measurement is performed. Meanwhile the instrument will remain performing measurements.

- New Histogram I/O

A Histogram I/O is added to the software. This I/O converts a signal into a histogram, showing the distribution of the different values within the signal. The result can be shown in a graph.

New Power Spectral Density I/O

A Power Spectral Density I/O is added to the software. This I/O performs a Power Spectral Density analysis of a signal. Power Spectral Density is a distribution that tells about the average power distribution over a range of frequency components.

- New units for logarithmic presentations

Several new units have been added for logarithmic representation of signals. A logarithmic (vertical) axis in a graph can now be set to the following units:

- dB
- dBV
- dBmV
- dBµV
- dBµV/m (at 10 m)
- dBm

The Log I/O now has the corresponding presets.

- And many more changes

Read more in the news section on our website https://www.tiepie.com/news

13/06/2024

Multi Channel oscilloscope software version 1.47 is released.
A lot of changes have been made to add new functionality and to improve basic operations in the software.

- Phase cursors
When examining phase shift between signals, or examining other periodic signals like e.g. crankshaft signals, special Phase cursors can be switched on in the graph.

With these special cursors, the beginning and end of a cycle can be marked, which then is considered to be 0 to 360 degrees. It is also possible to mark that area as being 0 to 720 degrees, 0 to 100 % or some user defined range. The regular cursors can then be used to determine the angle of a specific position in the cycle. This angle is determined using linear interpolation between the two limits of the range.

For automotive applications, the new Phase cursors are also very useful, in identifying the different strokes of an internal combustion engine. When used in combination with a Crankshaft angle I/O, the different strokes are clearly identified in the crankshaft signal.

- New EV Charger Control Pilot Analyzer I/O
The process of AC charging an Electrical Vehicle (EV) using a Type 2 coupling can be monitored by analyzing the information that is transferred by the Control Pilot (CP) signal. The EV Charger Control Pilot Analyzer I/O can be used to analyze this signal and show the available amount of current that can be provided by the charging point and the status of the charging process.

- New Meter display options: showing non-numerical data and a single column display mode.

- Rearranging objects in the Object Tree
The order in which objects are listed in the Object Tree can be changed. This can be useful when e.g. the setup has been modified because objects were inserted or removed. The I/Os can then appear in an order which is not convenient. By dragging the objects with the Ctrl key pressed, a better ordering can be achieved.

- and many more changes.

Read more in the news section on our website.

17/07/2023

TiePie engineering has introduced the Wireless Multi Instrument Synchronization Module WCMI-8, the world’s first module to wireless synchronize multiple oscilloscopes over a long distance of up to 400 meters and combine them to a single instrument.

The WCMI-8 module is placed on the extension connector at the rear of each oscilloscope and the Multi Channel oscilloscope software automatically detects how many instruments are equipped with a WCMI-8 module. All detected oscilloscopes, connected via WiFi, LAN or USB, are combined to one single oscilloscope with a total number of channels that equals the sum of the number of channels of the detected oscilloscopes.
The WCMI-8 module has an internal automatic time synchronization system that takes care that all sample clocks of the oscilloscopes are synchronized. When a trigger occurs on one of the selected channels, all oscilloscopes will be triggered simultaneously and all signals will be synchronously visible on the display.

For more info, see

The Wireless Multi Instrument Synchronization Module WCMI-8, the world’s first module to wireless synchronize multiple oscilloscopes over a long distance of up to 400 meters and combine them to a single instrument.

12/07/2023

Multi Channel oscilloscope software version 1.46 is released.

A lot of changes have been made to add new functionality and to improve basic operations in the software.

- Show peaks and harmonics in the graph.
Each signal line in a graph can show peaks in the signal by placing markers in the top part of the graph, with lines to the actual peak.
The magnitude of the peak is shown in the marker, as well as a time stamp.

When the graph displays frequency domain data, a frequency spectrum, it can also show the harmonics, with harmonics number, frequency and magnitude.

- Auto reconnect
An Auto reconnect feature is added to the scopes.
When this feature is enabled and the instrument loses connection to the computer, the instrument remains present in the software. When the connection is established again, the instrument will be activated again and will resume performing measurements, using the same settings as before the connection was lost.

- Made THD measurement more accurate by using 'Advanced peak detection' to find the base frequency.

- An option was added to the record view scrollbar of a graph to shift 10 division (one view port) by keeping the Ctrl key pressed when clicking left or right of the slider or on the left or right button.

- and many more changes.

Read more at :

Version 1.46 of the Multi Channel oscilloscope software is now available for download.

22/12/2022

TiePie engineering wishes everybody a healthy, happy and prosperous 2023!

23/11/2022

Multi Channel oscilloscope software version 1.45 is released.

A lot of changes have been made to add new functionality and to improve basic operations in the software.

- User presets and preset worksets have been added to easily load and switch between often used setups
- An Auto setup settings window is added, to easily configure how Auto Setup works, and have it track changing signals.
- New signal analyzing I/Os are added:
- Maximum I/O, to determine the maximum value of a signal
- Minimum I/O, to determine the minimum value of a signal
- Maximum - Minimum I/O, to determine the peak to peak value of a signal
- Signal analyzing I/Os are improved
- RMS I/O: can now determine the RMS value per period in the signal
- Pulse decoder I/O now also supports a Z input (zero point reference)
- Signal clipping indicators added to graphs and meters

- And many other changes.

Read more at :

Version 1.45 of the Multi Channel oscilloscope software is now available for download.