Phone Repair Xpert

Phone Repair Xpert Expert In Repairing In All Kinds Of Smart Phones And Tablets. Instant Repair , Micro Soldering.

Fault:After Heavy Fall WiFi Address Was N/A In Settings And Wifi Button Was Grey Out.What I Do: I Reball The Sandwich B...
07/10/2023



Fault:After Heavy Fall WiFi Address Was N/A In Settings And Wifi Button Was Grey Out.

What I Do: I Reball The Sandwich Board Only That’s It,Wifi Is Working Good With Perfect signal Strength Now Phone Is Functional All Over As Usuall And My Customer Is So Happy👍

"Fault:Any one repairer had damage the 8 pads during changing of type C charging connector of laptop.What I Do:Relive a...
07/10/2023

"

Fault:Any one repairer had damage the 8 pads during changing of type C charging connector of laptop.

What I Do:Relive all 8 pads on PCB with jumper wire and install a new type c charging connector,now laptop is charging fast with perfect ampheres👍

(5g)Fault:The phone was damaged after falling hard on the ground but the screen was working fine.What I Do:I was change...
07/10/2023

(5g)

Fault:The phone was damaged after falling hard on the ground but the screen was working fine.

What I Do:I was changed the PCB board charging FPC connector and the problem was sloved and phone is functional as usual and my customer is so happy for this job👍

Fault:The phone had full shortage inside the PCB sandwich board.What I Do:I put the 3.0Volts into the PCB battery FPC c...
07/10/2023



Fault:The phone had full shortage inside the PCB sandwich board.

What I Do:I put the 3.0Volts into the PCB battery FPC connector in VBAT line it taked a little bit spark and the whole shortage had gone so i think a little bit capacitor was full short inside the sandwich board so when i put the voltages on VBAT line the capacitor was blast,Now the phone is fully functional and all customer important data was recovered👍

Fault:Phone had dipped in water approx 2 hours😳,near the area of CPU had covered with water very badly.What I Do:Firstl...
07/10/2023



Fault:Phone had dipped in water approx 2 hours😳,near the area of CPU had covered with water very badly.

What I Do:Firstly i wash the whole PCB board with petrol and then i change 2 capicator and one ic which is short due to water damage,now the phone is back to life and all customer important data is recovered👍

Fault:Face ID have not working,A repairman damaged a dot projector while installed a new screen.What I Do:I have a (AY-...
07/10/2023



Fault:Face ID have not working,A repairman damaged a dot projector while installed a new screen.

What I Do:I have a (AY-A108) device which is used for repair dot projector without microsoldering so now the face id was functional as usual and my customer is so happy👍

Fault:After A Little Bit Fall Phone Was At Not Charging,Means When You Plug In The Charger Into The Phone,It Shows 0% R...
07/10/2023



Fault:After A Little Bit Fall Phone Was At Not Charging,Means When You Plug In The Charger Into The Phone,It Shows 0% Remaing At Battery Sign.

What I Do: I Changed PCB Boards Battery FPC connector Because It Was Loose So Now The Phone Is Working Functional And All Customer Important Data Is Safe👍

Fault:After the heavy fall the phone is gone at searching and no service and the modem firmware is N/A in settings.What...
07/10/2023



Fault:After the heavy fall the phone is gone at searching and no service and the modem firmware is N/A in settings.

What I Do:When i separate the PCB sandwich board 12 round pads of the PCB upper sandwich board were damaged,so then i done all the 12 pads relive and the problem was sloved so now the phone is functional as usuall and all customer important Data is safe as well👍

Fault:After the phone fell on the ground it went to searching and no service as well and showing N/A at modem firmware ...
07/10/2023



Fault:After the phone fell on the ground it went to searching and no service as well and showing N/A at modem firmware in setting then a repairer software it then the phone got stuck on activation lock.

What I Do:I reball the PCB sanwich board perfectly only thats it.Now the phone is functional as usuall and my customer Is so happy👍

#1 GenerationFault:After Heavy Fall IPad Was Boot Looping At Apple Logo,When I Connect IPad With iTunes,iTunes Gives A...
28/05/2023

#1 Generation

Fault:After Heavy Fall IPad Was Boot Looping At Apple Logo,When I Connect IPad With iTunes,iTunes Gives An Error (4013)

What I Do: I Was Changed 2 Coils Near Power Management IC Because That Was Broken Due To Heavy Fall,Now IPad Was Working Functionally As Usuall👍

Fault:After Very Heavy Fall Phone Was At Not Charging,Means When You Plug In The Charger Into The Phone Phone Shows 0% ...
28/05/2023



Fault:After Very Heavy Fall Phone Was At Not Charging,Means When You Plug In The Charger Into The Phone Phone Shows 0% Remaing Only!

What I Do: I Changed Boards Battery FPC connector Because It Was Broken And Now Phone Is Working Functional As Usuall As Well As My Customer Is So Happy👍

Fault:Stuck At Apple Logo Because Phone Was Short At ChargingWhat We Do:Removed Shorted Component,From VDD Main Line,No...
27/05/2023



Fault:Stuck At Apple Logo Because Phone Was Short At Charging

What We Do:Removed Shorted Component,From VDD Main Line,Now Phone Is Functional As Usuall And All Customer Important Data Is Safe As Well👍

Address

Preston

Website

Alerts

Be the first to know and let us send you an email when Phone Repair Xpert posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Shortcuts

Share

Category