https://www.facebook.com/198876919968671/

Steve’s Saber Services

Home
United States
Mooresville, NC
Steve’s Saber Services

Offering custom installations on empty sabers.

03/03/2026

Here’s a Saberbay Sentry all done up for Scott. These hilts are always a fun install.

Specs

GHv4
Shtok eco v4 connector
CC chassis from Saberbay
2 button setup
Removable battery
28mm bass speaker

Thank you again Scott for letting me install this for you!

01/17/2026

Hey everyone! I will be out of the country until the 26th this month. I’ll probably be slow replying to messages, but I will get back to you as soon as I can. Looking forward to getting back to work when I get back!

01/15/2026

Hey everyone, here’s one last saber done up before I go on vacation. Today, we have a Saberbay Sentry all done up with a crystal chamber.

Specs

Proffie v2.2
Shtok eco v4 connector
Crystal reveal chassis from Saberbay
2 button setup
Removable battery
28mm bass speaker

I also went with a different grip for this hilt, and I think it suits it very well. Now I just need to get it powder coated!

01/09/2026

Good afternoon everyone! Here’s a Roman Props v2 all done up for my personal collection.

I’ve had this for a while, but it needed a little lathe work because the crystal chamber didn’t fit it 100% (it needed shaved down a little on the top), so I sent it to Juan Ramirez and he cut down the CC a bit with his lathe. He also designed the chassis, speaker holder, and switch section solution for me.

Specs
Proffie v3.9
Dual Crystal chamber (Rudy Pando)
Internal 18350 battery
2x shtok v4 connectors
1.3mm recharge port
28mm KR Sabers speaker

Thank you again Juan for helping me with the lathe work and chassis design!!

01/07/2026

Hey everyone! I know I’m a little late, but I hope you all had a very Merry Christmas and had a happy new year. Here’s an Ultrasabers Dark Apprentice v5 all done for Daylen.

This came to me as a stunt saber setup, and I swapped out all the electronics to upgraded it to neopixel and added a Golden Harvest soundboard.

Specs
GHv3
One button setup
Shtok v4 longpin connector with holder
Internal 18650 battery
2.1mm recharge port
Chassis from Saberbay
28mm speaker

Thank you Daylen for letting me upgrade this hilt for you!

12/27/2025

Good morning everyone. I hope everyone had a wonderful Christmas!! Here’s a Watto’s Junkyard Tusken Slayer gen 2 all done up for Phil.

This was sent to me with a damaged chassis, and I re-installed it with a new chassis.

Specs

Proffie v2.2
Shtok eco v4 connector w/ cover
Two button setup
2x accent LEDs
Removable battery
24mm speaker

Thank you again Phil for letting me get to work on this!

11/24/2025

Hello everyone and happy Monday! Here’s an 89 Sabers MPP all done up for Andy. This hilt is the ESB version of the MPP hilt.

Specs

GHv4
Chassis from Saberbay
Shtok v4 pixel connector
2 button setup
Removable battery
31mm bass speaker

11/21/2025

Hello everyone, here is a saber all done up for my personal collection. This is an Elf Sabers Kylo that originally had a proffie basic install. I gutted it, installed a crystal chamber chassis and CFX.

Specs

CFX
3x Shtok eco v4 pixel connectors
Eco CC chassis from Goth 3D Designs
Two button setup
Removable battery
2x pixel accents for the crystal chamber
28mm bass speaker

11/19/2025

Hello everyone! Here we have a Saberz Maul all done up for Phil. This is the absolute best Maul hilt that I’ve seen.

Specs for both chassis

2x Proffie v3.9
2x Shtok V4 pixel connectors
2x pixel accent strip below the pixel connector
4x square red accent LEDs
2x 24mm bass speaker
Chassis from Tierfon Orbital

Thank you again Phil for letting me work on this hilt, and thank you to Tim from Tierfon Orbital for the chassis design. The engineering on this hilt is fantastic and on point. I hope Saberz makes another run because I need to get one now.

10/27/2025

Good morning everyone! Here’s another saber all done up for Phil. This time we have a KR Scavenger.

Specs

Proffie v3.9
One button setup
Shtok v4 long pin connector
Eco chassis from Goth 3D Designs
6-Trace rotary pcb
28mm bass speaker

I wanted to give a huge shoutout to Khal over at KR Sabers for helping me with a few things while installing this hilt.

Thank you again Phil for letting me install this saber for you!

10/25/2025

Good morning everyone. Here’s an OWK1 by KR Sabers done up for Phil.

This one came to me with a damaged chassis, so I took all the components out and re-installed it with a new chassis.

Specs

Proffie v2.2
Eco CC chassis from Goth 3D Designs
Shtok v4 longpin connector with lens cover
Two button setup
Removable battery
28mm speaker from KR Sabers

Thank you again Phil for letting me install your saber!

Address

Mooresville, NC
28115

Website

facebook.com

Alerts

Be the first to know and let us send you an email when Steve’s Saber Services posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Contact The Business

Send a message to Steve’s Saber Services: